mercury26
10-10-2016, 02:30 PM
So I am attempting to INPA and NavCoder working a WinXP SP3 instance and could use some help. I have used two different; K-DCAN and KKL cables but game the same result. When I hook the cable up to the car, place the ignition in Position 2 and start INPA, INPA will highlight the Ignition and Battery indicators (assuming showing connectivity to the car), but when I read a module it does return any data. With NavCoder will recognize the cable, but when I attempt to read the module it throws an error that it did not respond, sample error message below. I set the cable for Latency timer from default 16 msec. to 1 msec,as indicated by the instructions for both cables I tried.
Any thoughts? I am pretty well stumped on what to try next.
9/26/2016 9:59:40 PM.531: 3F 03 02 00 3E
9/26/2016 9:59:40 PM.531: DIA --> EKM : Read identity
9/26/2016 9:59:40 PM.984: 3F 03 02 00 3E
9/26/2016 9:59:40 PM.984: DIA --> EKM : Read identity
9/26/2016 9:59:41 PM.296: 3F 03 02 00 3E
9/26/2016 9:59:41 PM.296: DIA --> EKM : Read identity
9/26/2016 9:59:41 PM.718: 3F 03 02 00 3E
9/26/2016 9:59:41 PM.718: DIA --> EKM : Read identity
9/26/2016 9:59:42 PM.125: 3F 03 02 00 3E
9/26/2016 9:59:42 PM.125: DIA --> EKM : Read identity
9/26/2016 9:59:42 PM.546: 80 03 02 01 80
9/26/2016 9:59:42 PM.546: IKE --> EKM : Device status request
9/26/2016 9:59:42 PM.968: 80 03 02 01 80
9/26/2016 9:59:42 PM.968: IKE --> EKM : Device status request
9/26/2016 9:59:43 PM.375: 80 03 02 01 80
9/26/2016 9:59:43 PM.375: IKE --> EKM : Device status request
9/26/2016 9:59:43 PM.796: 80 03 02 01 80
9/26/2016 9:59:43 PM.796: IKE --> EKM : Device status request
9/26/2016 9:59:44 PM.218: 80 03 02 01 80
9/26/2016 9:59:44 PM.218: IKE --> EKM : Device status request
Single Module scan conducted on 9/26/2016 9:59:40 PM
--------------------------------------------------
Following devices were found and are communicating:
--------------------------------------------------
Summary of stored Fault Codes:
No Stored Fault Codes found.
--------------------------------------------------
The following devices did not respond:
They are either not fitted, not turned on, or not communicating on the databus.
EKM Body Electronics Module
Tips for devices that do not communicate:
--> Check device is fitted to vehicle
--> Check ignition is turned on
--> Check device is switched on
Any thoughts? I am pretty well stumped on what to try next.
9/26/2016 9:59:40 PM.531: 3F 03 02 00 3E
9/26/2016 9:59:40 PM.531: DIA --> EKM : Read identity
9/26/2016 9:59:40 PM.984: 3F 03 02 00 3E
9/26/2016 9:59:40 PM.984: DIA --> EKM : Read identity
9/26/2016 9:59:41 PM.296: 3F 03 02 00 3E
9/26/2016 9:59:41 PM.296: DIA --> EKM : Read identity
9/26/2016 9:59:41 PM.718: 3F 03 02 00 3E
9/26/2016 9:59:41 PM.718: DIA --> EKM : Read identity
9/26/2016 9:59:42 PM.125: 3F 03 02 00 3E
9/26/2016 9:59:42 PM.125: DIA --> EKM : Read identity
9/26/2016 9:59:42 PM.546: 80 03 02 01 80
9/26/2016 9:59:42 PM.546: IKE --> EKM : Device status request
9/26/2016 9:59:42 PM.968: 80 03 02 01 80
9/26/2016 9:59:42 PM.968: IKE --> EKM : Device status request
9/26/2016 9:59:43 PM.375: 80 03 02 01 80
9/26/2016 9:59:43 PM.375: IKE --> EKM : Device status request
9/26/2016 9:59:43 PM.796: 80 03 02 01 80
9/26/2016 9:59:43 PM.796: IKE --> EKM : Device status request
9/26/2016 9:59:44 PM.218: 80 03 02 01 80
9/26/2016 9:59:44 PM.218: IKE --> EKM : Device status request
Single Module scan conducted on 9/26/2016 9:59:40 PM
--------------------------------------------------
Following devices were found and are communicating:
--------------------------------------------------
Summary of stored Fault Codes:
No Stored Fault Codes found.
--------------------------------------------------
The following devices did not respond:
They are either not fitted, not turned on, or not communicating on the databus.
EKM Body Electronics Module
Tips for devices that do not communicate:
--> Check device is fitted to vehicle
--> Check ignition is turned on
--> Check device is switched on