PDA

View Full Version : BMW E46 Water Pump Failure Diagnosis and Replacement doityourself



3ZHPGUY
12-20-2010, 06:37 PM
BMW E46 (including ZHP) Water Pump Failure Diagnoses and Replacement
Parts required and suggested
• New BMW OEM Water Pump
• BMW Recommended Coolant, (Antifreeze)
• Idler Pulley, these pulleys are lubed when made and never again, good PM
• Tensioner Pulley, these pulleys are lubed when made and never again, good PM
• New Belt
Tools
• 1) Set of 3/8 drive metric sockets. 8mm- 15mm
• 1) Set of metric wrenches. 8mm – 15-mm
• 1) Set of Torx Drivers
• 1) 8 mm Alan Wrench and a 10” piece of pipe to extend it

E46 water pumps can fail in two ways.

http://i591.photobucket.com/albums/ss351/3zhpguy/Water_Pump/Vent_Hole_2.jpg

In the first case they can leek through the vent hole in the pump. In the illustration above it is very easy to see the vent hole. In the car it’s not as easy as it is located behind the Water pump Pulley.

http://i591.photobucket.com/albums/ss351/3zhpguy/Water_Pump/IMG_5879-1.jpg

The second failure is catastrophic as shown in the picture below. In this case the car can no longer move under its own power for any distance without overheating.

http://i591.photobucket.com/albums/ss351/3zhpguy/Water_Pump/IMG_4011_2.jpg

What led me to finding my second water pump bad was the Low Coolant indicator light coming on. The cooling system is a sealed system and this light will never come on in less there is a leek. My first step was to add coolant and monitor when it came on again and checking it periodically. There is a float in the expansion tank for the correct level. Be careful not to fill it to the top as I did, my tech told me that could cause the expansion tank to explode. BMW recommended fill instructions at the end of this article. The next thing to do is to do or have a pressure check done. Below is a picture of a pressure checker and the run from $50.00 to $200.00. I personally opted to have my BMW dealer do this for me at a Pre quoted cost of ½ hour labor $45.00.

http://i591.photobucket.com/albums/ss351/3zhpguy/Water_Pump/PressureChecker.jpg

Once my car was diagnosed by the BMW service facility, and I knew what was needed. I ask them to button it up and put the needed parts and fluid in the car. Note; I do use aftermarket parts on my ZHP, but anything internal to the engine I will only use BMW OEM parts.

Part II Replacing the Water Pump on my ZHP
Before starting the project make sure the car is COLD and has sat for at least TWO HOURS. The Coolant system is under severe pressure when hot. OPINING A HOT SYSTEM WILL CAUSE BURNS TO YOUR FLESH.
First you must remove the air duct form the top or the radiator. This is done by pulling up three plastic pins to allow the expansion pins to collapse and be removed AS SHOWN IN THE PICTURE BELOW.

http://i591.photobucket.com/albums/ss351/3zhpguy/Water_Pump/IMG_5856.jpg

http://i591.photobucket.com/albums/ss351/3zhpguy/Water_Pump/IMG_5858.jpg

Next remove the 2 electrical plugs and un-hook the wires from the retaining clip.

http://i591.photobucket.com/albums/ss351/3zhpguy/Water_Pump/IMG_5860.jpg

http://i591.photobucket.com/albums/ss351/3zhpguy/Water_Pump/IMG_5861.jpg

http://i591.photobucket.com/albums/ss351/3zhpguy/Water_Pump/IMG_5862.jpg

Next remove the 2 Torx screws from the top of the fan

http://i591.photobucket.com/albums/ss351/3zhpguy/Water_Pump/IMG_5863.jpg

Now remove the fan by pulling it in the upward motion

http://i591.photobucket.com/albums/ss351/3zhpguy/Water_Pump/IMG_5865.jpg

The next thing you will need to do is loosen the four bolts holing the pulley to the water pump. Note; if you forget to do this before removing the belt you will have a heck of a time because the water pump will rotate freely.

http://i591.photobucket.com/albums/ss351/3zhpguy/Water_Pump/IMG_5878.jpg

Next, pry off the covers on both the Idler and Tensioner Pulleys.

http://i591.photobucket.com/albums/ss351/3zhpguy/Water_Pump/IMG_5867.jpg

The next step is to remove the belt. The quickest and easiest way to do this is by rotating the tensioner pulley. This is the smaller pulley under the Idler Pulley and above the Power Steering Pulley. Find an 8 mm Allen wrench to fit the bolt in the center of that pulley and a pipe or wrench to extend the Allen Wrench. Rotate it slightly to remove the tension and have a friend remove the belt.

http://i591.photobucket.com/albums/ss351/3zhpguy/Water_Pump/IMG_5878.jpg

Before you go any further I suggest that you hang a towel over the radiator. This will protect it in the case of a fallen tool or part. It’s bad enough to drop a tool in a place that is hidden or hard to get to but, watching it fall against the radiator followed by a small stream of coolant coming from the point of impact, is by far more irritating and costly.
Once the belt is out of the way remove the 4 bolts holding on the water pump pulley. Next remove the pulley. This can be a little daunting as it is a very tight fit to a flange on the water pump. What I have done that worked, was to tap the front outside of the pulley wile rotating it. Just slight taps because, cocking it too much will cause binding and possible damage to the pulley.

http://i591.photobucket.com/albums/ss351/3zhpguy/Water_Pump/IMG_5877.jpg

Now you are down to the Water Pump. If you are doing the pressure check and can’t find the leek, this is how far you need to be to tell if the pump is leaking through the vent hole pictured earlier. You may need a mirror to see the vent hole on the bottom side of the water pump. Note; this is how far the Tech at the BMW dealer had mine apart before he gave me the diagnoses that the pump was bad and the area my coolant was escaping from.

http://i591.photobucket.com/albums/ss351/3zhpguy/Water_Pump/IMG_5869.jpg

To Change the Pump remove the 4 nuts. From here there are two ways of removing the pump. Between the side holes there are 2 metric treaded holes. Matching bolts can be threaded in to these holes that will act as a puller. The method I used was to gently rock and pull the water pump out. At this point the only thing holding the pump in place is a rubber O-Ring. The picture of the new pump below will give you an idea of what is inside.

http://i591.photobucket.com/albums/ss351/3zhpguy/Water_Pump/IMG_5873.jpg

The next picture shows the engine with the water pump removed.

http://i591.photobucket.com/albums/ss351/3zhpguy/Water_Pump/IMG_5871.jpg

From this point reverse the process putting everything back together but, don’t fill the radiator until reading that procedure. I may also suggest using Engine Assembly Lube or Vaseline on any metal components that may be a close fit. The items I’m referring to ate the outside diameter O-Ring area on the Water Pump and the inside diameter of the water pump pulley.

http://i591.photobucket.com/albums/ss351/3zhpguy/Water_Pump/IMG_5874.jpg

After everything is back together similar to the picture below, it’s time to fill the coolant.

http://i591.photobucket.com/albums/ss351/3zhpguy/Water_Pump/IMG_5879.jpg

Remove the coolant cap and THE BLEEDER SCREW. Failure to remove the bleeder screw will result in air in the system. If this happens the car will overheat.

http://i591.photobucket.com/albums/ss351/3zhpguy/Water_Pump/IMG_4017_3.jpg

Slowly fill the expansion tank with specified coolant. According to the E45 Owner’s manual “The coolant level is correct when the upper end of red float is at least even with the upper edge of the filler neck. The end of the float may stick out a maximum of ¾” inch – that is, up to the second mark on the float.”

http://i591.photobucket.com/albums/ss351/3zhpguy/Water_Pump/IMG_5882.jpg

Note; this is usually mixed 50/50 with water. Having too much water will risk the possibility of freeze up in cold weather or over heating in worm weather. If you want to check how good, or how low your coolant temp is good for you need an Antifreeze Hydrometer and they are available at your local pars store.
Once complete cap off the expansion tank and the bleeder. Start the car and let it heat to the normal midpoint on the data in the car. I suggest only taking the car on close test drives and paying very close attention to the gage on the dash. If it does overheat bring it home and weight until it cools for a few hours before attempting to bleed the system again. This system is under severe pressure when hot. Opening THE CAP WHEN HOT CAN AND WILL CAUSE SEVERE BERNS TO YOUR FLESH.

Good luck,
3ZHPGUY

Marcus-SanDiego
12-20-2010, 06:40 PM
Guy, great write up. I don't work on my own car but I sure as hell respect the way you detailed that job.

pyreguy
12-20-2010, 06:53 PM
Very nice writeup! I will definitely use this when the time comes.

Linh
12-20-2010, 06:59 PM
Very nice write up. Will be using it as a guide when I do mine in a week or two!

3ZHPGUY
12-20-2010, 06:59 PM
Thanks, I figure it's a little too far to come and help so, the more in site I can share the better for all.

Marcus-SanDiego
12-20-2010, 07:14 PM
Guy, you ain't that far from me. Ha!

danewilson77
12-21-2010, 04:25 AM
Nice writeup. Thanks for posting....

***I will however recommend anyone doing the above, should also replace upper and lower coolant hoses, T-stat, exp tank, temp sensor....or else...you may be spending more time on your coolant system soon. The entire overhaul is what I recommend.

Linh
12-21-2010, 09:59 PM
1) 8 mm Allen Wrench and a 10” piece of pipe to extend it

I probably missed it, but where do we use this tool?

danewilson77
12-22-2010, 05:19 AM
Additionally.....replace "water" with "distilled water", and where you talk about adding the coolant.....refer to the coolant bleed procedure and mention that raising the front end of the car to facilitate air bleed.

3ZHPGUY
12-22-2010, 01:21 PM
1) 8 mm Allen Wrench and a 10” piece of pipe to extend it

I probably missed it, but where do we use this tool?

The 8mm Allen Wrench and the pipe are used to remove the Belt. That is the size of the Allen Bolt in the center of the Tensioner pulley. Rotate tat Tensioner to remover the tension from the belt and someone else can remove the belt from the pulleys wile you have the tension off.

JohnnyGraphic
01-24-2011, 05:00 PM
Nice writeup. Thanks for posting....

***I will however recommend anyone doing the above, should also replace upper and lower coolant hoses, T-stat, exp tank, temp sensor....or else...you may be spending more time on your coolant system soon. The entire overhaul is what I recommend.

I second the recommendation to replace the hoses, thermostat, expansion tank and temp sensor.

To that, I will also add to replace the Idler Pulley, Accessory pulley, Alternator pulley, Serpentine Belt (Accessory belt) and A/C belt. You'll have most everything off and right in front of you. You only need to take a few more steps and it's easy, not that expensive and consolidates the entire system.

I did my cooling system about 10k miles ago, but didn't replace the A/C pulley or the lower hose (couldn't get the stinking thing off!) or the temp sensor. I *JUST* (2 days ago) replaced the A/C pulley since it was making noise. Now, I noticed that the temp sensor in the lower hose is leaking just a smidgen. Now, I have to pull the fan off and will probably go thru and replace what I should have a year ago.

Johnny

Marcus-SanDiego
01-24-2011, 05:06 PM
I second the recommendation to replace the hoses, thermostat, expansion tank and temp sensor.

To that, I will also add to replace the Idler Pulley, Accessory pulley, Alternator pulley, Serpentine Belt (Accessory belt) and A/C belt. You'll have most everything off and right in front of you. You only need to take a few more steps and it's easy, not that expensive and consolidates the entire system.

+1

JohnnyGraphic
01-24-2011, 05:19 PM
Here is a pic of my water pump with 70k miles on it. The impeller part of the pump looked fine. I don't remember if it felt bad or made any noise or not. But, you can see the coolant seeping from the weep hole. There was coolant residue on the inside of the pulley too.

Johnny

danewilson77
01-24-2011, 05:27 PM
I second the recommendation to replace the hoses, thermostat, expansion tank and temp sensor.

To that, I will also add to replace the Idler Pulley, Accessory pulley, Alternator pulley, Serpentine Belt (Accessory belt) and A/C belt. You'll have most everything off and right in front of you. You only need to take a few more steps and it's easy, not that expensive and consolidates the entire system.

I did my cooling system about 10k miles ago, but didn't replace the A/C pulley or the lower hose (couldn't get the stinking thing off!) or the temp sensor. I *JUST* (2 days ago) replaced the A/C pulley since it was making noise. Now, I noticed that the temp sensor in the lower hose is leaking just a smidgen. Now, I have to pull the fan off and will probably go thru and replace what I should have a year ago.

Johnny

I have o-rings that fit that temp sensor perfectly if you're interested.....

Mtnman
01-24-2011, 05:42 PM
I just replaced the original wAter pump in mine. 135k miles on it. Was not bad, but i had a bad thermostat, and so i got that done at the same time as pm. Just fyi.

JohnnyGraphic
01-24-2011, 05:47 PM
I have o-rings that fit that temp sensor perfectly if you're interested.....

PM sent.

danewilson77
01-24-2011, 07:10 PM
Responded. Mailing tomorrow...

Sent from my Droid using Tapatalk

billschusteriv
02-14-2011, 07:57 AM
Additionally.....replace "water" with "distilled water", and where you talk about adding the coolant.....refer to the coolant bleed procedure and mention that raising the front end of the car to facilitate air bleed.

+1 on the distilled water. Very important. Too many impurities in tap water to put into your coolant system.

Also consider buying a high quality aftermarket water pump or BMW OE water pump. I picked up an aftermarket/OEM pump for my e30 (not in a BMW box, but manufactured by the original equipment manufacturer - GRAF, IIRC) and the bearings went after 10,000-15,000 miles of use and it leaked water out along the shaft. And no, my belts were not too tight. Never had a problem before with OEM parts... used this part twice before on my e30 with much success.

llll1l1ll
05-25-2011, 07:16 AM
Anybody know how long this job would take for the average shadetree mechanic?

Takes me the entire day on my E30. Seems like there is a lot less to do on the E46.

3ZHPGUY
05-25-2011, 09:36 AM
Anybody know how long this job would take for the average shadetree mechanic?

Takes me the entire day on my E30. Seems like there is a lot less to do on the E46.

You should be able to complete the job in 4 hours. Plan on 6 and use the extra to drink beer in celebration of your completed task.

llll1l1ll
05-25-2011, 11:41 AM
Four hours?? All the more reason to get a ZHP now!

kayger12
05-25-2011, 01:01 PM
Yep-- easiest car you'll ever work on.

llll1l1ll
05-27-2011, 09:27 AM
Yeah the engine bay looks completely uncluttered in the E46 compared to my E30. Plus, everything won't be coated in 22 years worth of grime.

das boots
09-27-2011, 12:12 PM
I remember seeinga thread that has a seller selling the whole package for the whole enchilada with the exception of the water pump by replacing with a better one...Thanks.