I'd say just buy a MIG and go for it. It won't take long to learn.
Type: Posts; User: squashman702
I'd say just buy a MIG and go for it. It won't take long to learn.
Replaced the cabin filter today and looked over the rear subframe- the rear bushing for the diff has some cracking, so I just ordered Lemforder replacements for that and the two front diff bushings. ...
Installed Bilstein B4's all around on Friday along with new mounts in the front, and reinforced mounts in the rear. Got everything back together and realized I had missed the washer between the...
Spent a few minutes at my shop working on the ZHP. Headlights needed to be cleaned up bad.
Practiced on the M3 lights:...
Nothing to the ZHP, but hung some stuff on the LS1 for the ///M today.
http://i243.photobucket.com/albums/ff295/squashman702/Mobile%20Uploads/20160609_173436_zpsxtoxwpmv.jpg
Sorry to hear you had to sell.
I have the white YZ250f, the others are a 91 DR350 getting a 1mm overbore, and a 2001 KX125.
Gave it some TLC today, fixed the shield over the fuel filter, stitched together the cracked lower lip of my front bumper, and fixed a loose fender liner. Also gave it an oil change with M1 and a...
Vacuumed then cleaned and conditioned the leather with Lexol stuff.
Nothing for the ZHP, but made a little progress on the M3 today. Put in the black carpet I had, and the Modena rear seat and sport front seats. Have some vaders to refinish at some point down the...
How was the meet?
Nothing on the ZHP this weekend, but gave the M3 some attention.
Subframe pulled, doing AKG reinforcement plates for RTAB, rear sway, and rear strut towers.
...
Friday night I did:
-Expansion tank
-Radiator
-Upper and lower hoses
-Thermostat and housing
-Water pump
-Coolant level sensor
-BMW coolant/distilled water
Saturday:
That or I am getting too good at recognizing a misfire . . . the advantage of having a bunch of shitty vehicles prior to owning a decent one.
Scanner came up with two P0301 codes, misfire on cylinder one. Swapped the coil and all seems to be good- misfire is definitely cleared up. Hopefully nailed the bullseye with the first throw of...
Yeah, going to pull the codes later. Scanner is at my shop and my cars never seem to break down there. I used whatever Bosch plugs were suggested when I changed them.
Thinking it's probably the coil pack(s). I did plugs ~45k or so ago- maybe less, I'd have to check my records- so they don't seem like the likely culprit. I ordered a coil pack last night just in...
Think I have a misfire, car started running super rough about 3/4 of a mile from where I live and got a CEL. Shut the car off then started it again, started to run rough again. Will a normal code...
Drove it to my shop to go clean carbon for a couple of hours.
http://i243.photobucket.com/albums/ff295/squashman702/Mobile%20Uploads/20160323_201437_zps49gosd4a.jpg
Replaced the fuel pump and seal with a Siemens/VDO unit. Luckily it died in a spot where I could leave the car for the weekend, ordered a new pump from Bavarian Auto Sport on Thursday night and had...
I used the "F" shaped vacuum line that goes into the upper intake boot. I've used it on a bunch of my vehicles without issue, but the ZHP was the least phased by it going in (normally they stall or...
Mobil M1 and a Mann filter for it today, but seafoamed first. Biggest cloud of smoke I've seen in all of my seafoam experience.
Mine was a passenger side issue as well, replaced the whole handle after I tried to clean up the corrosion. It was around $100 at the dealer after tax.
New trunk latch, one of the license plate bulbs was out due to massive amounts of corrosion. Tried to get the glue to release on the factory handle cover by baking it for a bit, didn't work. This...
Passenger side airbag recall done.
New BMW valve cover gasket today, replacement one I did last was leaking out of the rear most bolt in the center. No oil leaks for now.