Materials to Maintain Your ZHP IIIII Hand Protection IIIII Tools to Maintain Your ZHP

Search:

Type: Posts; User: REF84

Page 1 of 3 1 2 3

Search: Search took 0.03 seconds; generated 25 minute(s) ago.

  1. Replies
    3
    Views
    672

    Had a similar issue today. I already have the...

    Had a similar issue today. I already have the thermostat and water pipe removed. I’m going to get one of those little boroscope camera things and see if I can find it. Otherwise I think I might use...
  2. Thanks @RUS_ZHP. What 27mm aftermarket bar did...

    Thanks @RUS_ZHP. What 27mm aftermarket bar did you upgrade to? You used the same end links when you upgraded to the 27mm bar? And they were in good shape?
  3. This was sold on another forum

    This was sold on another forum
  4. Fitting M3 front sway bar using OEM endlinks

    I've seen mixed opinions on this so starting a thread. I'm looking for an upgraded front sway bar for my ZHP on stock springs/koni SAs. I have a junkyard Xi bar for the rear. The M3 coupe/vert bar...
  5. Now offering shipping!

    Now offering shipping!
  6. Replies
    26,149
    Views
    6,189,946

    That’s the e85 z4 wheel, I just bought a mint...

    That’s the e85 z4 wheel, I just bought a mint condition one to throw into my ZHP as well.
  7. if you track that much then I'd get a steel...

    if you track that much then I'd get a steel single mass from clutchmasters. More weight than aluminum so wont be so touchy. It was my second choice but I most likely wont track my car much.
  8. What do you mean “super difficult to drive set...

    What do you mean “super difficult to drive set up”? I haven’t installed yet but decided to go stock LUK. Only $550 for clutch and flywheel from RockAuto. I’ve read so many stories about folks not...
  9. Surprised no bites on anywhere. Guess the market...

    Surprised no bites on anywhere. Guess the market is rough. I’ll be installing a new clutch, rebuilding starter, and doing intake manifold/cooling system. If it’s still not sold by then I’ll just...
  10. Yes absolutely This is a pretty good pdf by...

    Yes absolutely

    This is a pretty good pdf by paraklas from e46fanatics on the install, he also welds plate just skip that part:
    ...
  11. Down to $550 someone take it

    Down to $550 someone take it
  12. price drop to $600 for the mafia

    price drop to $600 for the mafia
  13. Replies
    3
    Views
    1,950

    I know this is 3 years old but....do you still...

    I know this is 3 years old but....do you still have this?
  14. Hey Will, I did my control arms a little while...

    Hey Will, I did my control arms a little while back and im sort of concerned about the torque process. Did you load the suspension when you torqued everything? I used a jack to lift up the suspension...
  15. (Sold): Vincebar Epoxy Kit (rear bar, front gussets, hardware and tools)

    I have a new unused vincebar epoxy kit. It is the latest version of the bar with the front gussets, all the hardware, drillbits and rivets necessary to install. Everything here except the candy
    ...
  16. Replies
    1,180
    Views
    219,930

    You're Welcome! Looking Good!!!!! How was the...

    You're Welcome! Looking Good!!!!!

    How was the install?
  17. considering new clutch, go with OEM Luk or go with a steel SMF for occasional track day? Non-adjustable clutch options?

    Since it's wintertime I'm in no rush to get my car ready. Im doing the flex disc and shifter bushings and tranny mounts, so replacing the clutch is just a couple more bolts away, so I figure I do it...
  18. Replies
    3
    Views
    899

    For a cheap fix you could try a clutch stop, that...

    For a cheap fix you could try a clutch stop, that helped me a lot. You can get one for example from bimmerworld. You just screw it in to a little hole behind the clutch, it acts as a stopper to...
  19. Replies
    44
    Views
    7,902

    Vincebar came in today, paid the invoice on 9/26,...

    Vincebar came in today, paid the invoice on 9/26, so a little over a week to arrive at my doorstep. This is the epoxy/rivet kit + toolkit. And some Swedish candy.

    https://i.imgur.com/SOYwM0H.jpg
  20. Replies
    44
    Views
    7,902

    I decided to keep the turner kit then. Not worth...

    I decided to keep the turner kit then. Not worth the hassle. They had their DSSR for our cars on sale so I snagged it.

    My ctmotorsport1 aluminum subframe bushings came in along with the Turner...
  21. Easiest way to paint and rust proof diff, subframe, vincebar kit (no spray paint)

    I have my diff and subframe out and there is some rust on both. I will also be doing the vincebar kit which will involves cutting into the trunk and seat area and installing some steel plates/bars. I...
  22. Replies
    44
    Views
    7,902

    No particular reason, but I already have the...

    No particular reason, but I already have the rogue transmission mounts and oem m3 engine mounts in my possession. I would have to sell the RE tranny mounts and then buy the m3 tranny mounts. So im...
  23. Replies
    44
    Views
    7,902

    Which transmission mounts did you try before? ...

    Which transmission mounts did you try before?

    Im looking at reviews in the nam3 forum/e46fanatics/bimmerforums and I havent found someone say something bad about the rogue mounts (yet). I even...
  24. Replies
    5
    Views
    1,994

    Thanks I was pondering it last night and went...

    Thanks I was pondering it last night and went with the achilles pump shaft (pre-pressed) and the baffled oil pan from moreheadspeedworks. Tried finding some local welders to do aluminum and it was a...
  25. Replies
    44
    Views
    7,902

    I have these:...

    I have these: https://www.rogueengineering.com/Rogue-Engineering-Transmission-Mounts_p_137.html

    It says theyre neoprene and are "compliant for street use". And bimmerworld describes them as...
Results 1 to 25 of 69
Page 1 of 3 1 2 3