Search:

Type: Posts; User: sillieidiot

Page 1 of 20 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    5
    Views
    432

    it should only be like 6 lock nuts and 6 washers....

    it should only be like 6 lock nuts and 6 washers. you can get them anywhere.
  2. Nope. They did on like the early model e46s...

    Nope. They did on like the early model e46s though.
  3. Thread: DIY meet?

    by sillieidiot
    Replies
    16
    Views
    1,915

    Yeah you guys might have to do it without me. But...

    Yeah you guys might have to do it without me. But I'll at least try to get shit set up. I'm free the second half of June up to mid-July so far it looks like. Dunno about August, too far out. Then...
  4. Replies
    6,752
    Views
    403,932

    Just use a large c-clamp. I would leave the pad...

    Just use a large c-clamp. I would leave the pad that is attached the to piston on so that you could use it as a contact point for the c-clamp to push the piston back. Other than that, maybe just use...
  5. Thread: DIY meet?

    by sillieidiot
    Replies
    16
    Views
    1,915

    Maybe we'll hold one after we install your stuff....

    Maybe we'll hold one after we install your stuff. We need a cheap POS car to test it out on lol
  6. Aren't they like the autozone brand? You should...

    Aren't they like the autozone brand? You should try to check out R1concepts if they are still around. They sell Centric (parent company of Stoptech) brake parts for pretty cheap. At least I remember...
  7. Replies
    11
    Views
    289

    Well the first time I did it, it was on jack...

    Well the first time I did it, it was on jack stands. So yeah you lower it and then you just struggle until you get it lol But the second time, I did it on my lift. So much easier, but same thing. We...
  8. Replies
    6,752
    Views
    403,932

    i'm pretty sure the rear needs some modifications...

    i'm pretty sure the rear needs some modifications unless you're not that low.
  9. Replies
    644
    Views
    27,208

    Yep, AW master race lol Damn so jealous. I wanted...

    Yep, AW master race lol Damn so jealous. I wanted that exact car. But I ended up with the Model 3 because there was no way I was going to share the M2 with the rest of the family lol
  10. Replies
    11
    Views
    289

    Well you could reuse a lot of stuff. but I don't...

    Well you could reuse a lot of stuff. but I don't think it saves you that much. Like you could reuse your 2 bearing pins, the circlip, and the dowel. what is that like $20? lol I don't think you need...
  11. Replies
    5
    Views
    235

    Nice. I still have mines just sitting at EAS lol...

    Nice. I still have mines just sitting at EAS lol iono when that will get installed. Hopefully this year.
  12. Replies
    11
    Views
    289

    link doesn't work for me.

    link doesn't work for me.
  13. Replies
    180
    Views
    15,447

    Are you sure you're reading it right? They should...

    Are you sure you're reading it right? They should have two options. One for any ratio that is less than or equal to 3.07. The other should be any ratio that is greater than or equal to 3.15. So you...
  14. Replies
    183
    Views
    20,232

    nice. yeah I still have mines sitting in a shed....

    nice. yeah I still have mines sitting in a shed. i'll get to it eventually. have to swaintech coat it first.
  15. It's not that hard to fish the wires out of the...

    It's not that hard to fish the wires out of the trunk. there's only like 2 large ones (reverse lights) and like 2 small plugs (trunk handle/latch). You will spend probably more time taking off the...
  16. Thread: DIY meet?

    by sillieidiot
    Replies
    16
    Views
    1,915

    So should we try again? June? lol I currently...

    So should we try again? June? lol I currently don't have anything going on in June afaik. Maybe my car will be done, but I doubt that too lol I'm pretty sure from all the other meets. We can only...
  17. I haven't done it on my car yet. but on other...

    I haven't done it on my car yet. but on other cars I've repaired, we just buy wire and I just solder and heat shrink everything. Then I would electrical tape the entire bundle of wires before shoving...
  18. Replies
    6,752
    Views
    403,932

    yes. go with swaintech since it's the best of the...

    yes. go with swaintech since it's the best of the three.
  19. mine wasn't hard to come off. you just wiggle it...

    mine wasn't hard to come off. you just wiggle it back and forth until it comes off. wiggle it..hehe lol
  20. Sticky: the rears are going to need some fender work

    the rears are going to need some fender work
  21. I feel like I should redo this entire project...

    I feel like I should redo this entire project thread. I do have all my update posts saved in OneNote. The only thing that sucks is the smileys are different so I would have to go back and fix them...
  22. Thread: DIY meet?

    by sillieidiot
    Replies
    16
    Views
    1,915

    Yeah we're horrible at this lol even when I...

    Yeah we're horrible at this lol even when I schedule stuff like 2 months out it didn't work lol but I gotta reseal the hydraulic cylinders on the lift anyways. Then transfer them to their new home...
  23. Replies
    644
    Views
    27,208

    Mmm white would be awesome. That's what I would...

    Mmm white would be awesome. That's what I would have gotten.
  24. Replies
    2
    Views
    160

    Do you need a brand new one or like one that's...

    Do you need a brand new one or like one that's already been cut works? Lol cause I'll have 2 available when you guys install my sc
  25. Get a ppi

    Get a ppi
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4