Had a similar issue today. I already have the thermostat and water pipe removed. I’m going to get one of those little boroscope camera things and see if I can find it. Otherwise I think I might use...
Type: Posts; User: REF84
Had a similar issue today. I already have the thermostat and water pipe removed. I’m going to get one of those little boroscope camera things and see if I can find it. Otherwise I think I might use...
Thanks @RUS_ZHP. What 27mm aftermarket bar did you upgrade to? You used the same end links when you upgraded to the 27mm bar? And they were in good shape?
This was sold on another forum
I've seen mixed opinions on this so starting a thread. I'm looking for an upgraded front sway bar for my ZHP on stock springs/koni SAs. I have a junkyard Xi bar for the rear. The M3 coupe/vert bar...
Now offering shipping!
That’s the e85 z4 wheel, I just bought a mint condition one to throw into my ZHP as well.
if you track that much then I'd get a steel single mass from clutchmasters. More weight than aluminum so wont be so touchy. It was my second choice but I most likely wont track my car much.
What do you mean “super difficult to drive set up”? I haven’t installed yet but decided to go stock LUK. Only $550 for clutch and flywheel from RockAuto. I’ve read so many stories about folks not...
Surprised no bites on anywhere. Guess the market is rough. I’ll be installing a new clutch, rebuilding starter, and doing intake manifold/cooling system. If it’s still not sold by then I’ll just...
Yes absolutely
This is a pretty good pdf by paraklas from e46fanatics on the install, he also welds plate just skip that part:
...
Down to $550 someone take it
price drop to $600 for the mafia
I know this is 3 years old but....do you still have this?
Hey Will, I did my control arms a little while back and im sort of concerned about the torque process. Did you load the suspension when you torqued everything? I used a jack to lift up the suspension...
I have a new unused vincebar epoxy kit. It is the latest version of the bar with the front gussets, all the hardware, drillbits and rivets necessary to install. Everything here except the candy
...
You're Welcome! Looking Good!!!!!
How was the install?
Since it's wintertime I'm in no rush to get my car ready. Im doing the flex disc and shifter bushings and tranny mounts, so replacing the clutch is just a couple more bolts away, so I figure I do it...
For a cheap fix you could try a clutch stop, that helped me a lot. You can get one for example from bimmerworld. You just screw it in to a little hole behind the clutch, it acts as a stopper to...
Vincebar came in today, paid the invoice on 9/26, so a little over a week to arrive at my doorstep. This is the epoxy/rivet kit + toolkit. And some Swedish candy.
https://i.imgur.com/SOYwM0H.jpg
I decided to keep the turner kit then. Not worth the hassle. They had their DSSR for our cars on sale so I snagged it.
My ctmotorsport1 aluminum subframe bushings came in along with the Turner...
I have my diff and subframe out and there is some rust on both. I will also be doing the vincebar kit which will involves cutting into the trunk and seat area and installing some steel plates/bars. I...
No particular reason, but I already have the rogue transmission mounts and oem m3 engine mounts in my possession. I would have to sell the RE tranny mounts and then buy the m3 tranny mounts. So im...
Which transmission mounts did you try before?
Im looking at reviews in the nam3 forum/e46fanatics/bimmerforums and I havent found someone say something bad about the rogue mounts (yet). I even...
Thanks I was pondering it last night and went with the achilles pump shaft (pre-pressed) and the baffled oil pan from moreheadspeedworks. Tried finding some local welders to do aluminum and it was a...
I have these: https://www.rogueengineering.com/Rogue-Engineering-Transmission-Mounts_p_137.html
It says theyre neoprene and are "compliant for street use". And bimmerworld describes them as...