Yes, it does. China. No big surprise but I have confidence that Hella oversees the quality aspect of their products manufactured by their partners
35412
Type: Posts; User: sparky300
Yes, it does. China. No big surprise but I have confidence that Hella oversees the quality aspect of their products manufactured by their partners
35412
Ordered it from Rockauto, $105 with tax and shipping. Shipped Thurs, arrived today.
Sure as sh*t it's a brand new casting, same as OEM 34116765881 without BMW stamp on it.
35399
35400
...
Looks like I've found the answers to all my questions.
http://brakeguide.hella-pagid.com/hpa/en_US/8AN%20355%20792-491_78/datasheet.xhtml
Complete caliper, new casting, no bracket, no core....
Welp, the PO broke off one of the front caliper bleeders nearly clean with the casting and THEN, managed to break the tip of an EZ-out inside. Undrillable. Is that a word? Soaking in PBB now. Will...
Where in NM are you?
It appears the Schmiedmann cats are set up virtually identical to the Supersprints with the only difference being the collector flanges are ball & socket type versus OEM flat flange and gasket and...
I might suspect one or both of the pre-cat O2's but I'd have to do some searching first to find the acceptance range values
Whatever header I end up with will also be ceramic coated before the install :thumbsup
Correct, limited placement for sure. Behind the trans after the offset is about the only location.
...
I know. Another header thread. I've searched many, many threads and I've found no conclusive answers anywhere to some of my questions concerning replacing the stock exhaust manifolds and adding...
Off work today. Oil change due and I had bought a new oil level sensor since I've never gotten a dash warning since I bought the car last year. Yes, the dash warning light works during the key on...
Fixed the link in my post. Here it is again, more than enough for this project plus wherever else anyone could find a use for it
...
Keep your eyes peeled for used on Fleabay. Picked mine up for $45 shipped, ashtray and all and it barely looked used, lid wasn't even scratched. Better than the one it replaced for sure
Just wanted to add to this discussion as I just did this this weekend.
Agreed. In fact, Dynamat explicitly describes this exact process. While I admit the factory crayon garbage had deteriorated...
Imo, there isn't any room back in that area for anything of any substantial dimension height-wise. It's pretty tight and I didn't want to put any additional pressure on the glass and louver, just...
Thanks!
Just below the bottom of the back glass the steel panel has raised areas and those make contact with the molded-in support ribs of the louver. I installed adhesive Teflon tape on the steel...
Spent the better part of the weekend stripping all the factory hot crayon sound-deadening, tar and insulation from the rear seat, trunk and shelf and replaced it with Dynamat and 1/2" Dynaliner. Took...
Pm'd
Done. PM or email me ...sparky300 at gm
This tow hook license plate holder came with my car, I neither need it or want it. It's complete with all hardware and in near new condition.
Given that these are not much more than $10 new, you...
I'm in
1. Wolfn8tr- 1
2. CakM3- 1
3. Karl Lazlo- 2
4. Badclown- 1
5. BP- 1
6. ZHP-Brandon- 1
7. Vas- 1
8. Sockethead- 1
Wow. These seem like a bargain given the fantastic condition that they're in. Almost makes me wish that I lived closer...and had a coupe...and leather...
GLWS
I prob made it sound worse than it actually is. It really was only the 3 inches of wiring to the solenoid that were closest to the refector and I took care of that with liquid electrical tape. I...
I agree, mine were no better after 14 years baking inside the housing. This way there is very little manipulation of the existing solenoid wires and reduced chance of insulation damage. The only...
I thought I'd post this info up given that I recently did the Morimoto projector install on my '04 that had the burnt bowl issue. I did a comprehensive search and couldn't definitively find that...
This.