Materials to Maintain Your ZHP IIIII Hand Protection IIIII Tools to Maintain Your ZHP

Search:

Type: Posts; User: sparky300

Page 1 of 2 1 2

Search: Search took 0.05 seconds.

  1. Replies
    5
    Views
    9,497

    Yes, it does. China. No big surprise but I have...

    Yes, it does. China. No big surprise but I have confidence that Hella oversees the quality aspect of their products manufactured by their partners

    35412
  2. Replies
    5
    Views
    9,497

    Ordered it from Rockauto, $105 with tax and...

    Ordered it from Rockauto, $105 with tax and shipping. Shipped Thurs, arrived today.

    Sure as sh*t it's a brand new casting, same as OEM 34116765881 without BMW stamp on it.

    35399

    35400
    ...
  3. Replies
    5
    Views
    9,497

    Looks like I've found the answers to all my...

    Looks like I've found the answers to all my questions.

    http://brakeguide.hella-pagid.com/hpa/en_US/8AN%20355%20792-491_78/datasheet.xhtml

    Complete caliper, new casting, no bracket, no core....
  4. Replies
    5
    Views
    9,497

    Hella/Pagid Calipers?

    Welp, the PO broke off one of the front caliper bleeders nearly clean with the casting and THEN, managed to break the tip of an EZ-out inside. Undrillable. Is that a word? Soaking in PBB now. Will...
  5. Replies
    7
    Views
    6,678

    Where in NM are you?

    Where in NM are you?
  6. It appears the Schmiedmann cats are set up...

    It appears the Schmiedmann cats are set up virtually identical to the Supersprints with the only difference being the collector flanges are ball & socket type versus OEM flat flange and gasket and...
  7. Replies
    7
    Views
    6,678

    I might suspect one or both of the pre-cat O2's...

    I might suspect one or both of the pre-cat O2's but I'd have to do some searching first to find the acceptance range values
  8. Whatever header I end up with will also be...

    Whatever header I end up with will also be ceramic coated before the install :thumbsup



    Correct, limited placement for sure. Behind the trans after the offset is about the only location.


    ...
  9. Replacing stock exhaust with headers and a hi-flow cats questions

    I know. Another header thread. I've searched many, many threads and I've found no conclusive answers anywhere to some of my questions concerning replacing the stock exhaust manifolds and adding...
  10. Replies
    26,149
    Views
    6,190,557

    Off work today. Oil change due and I had bought a...

    Off work today. Oil change due and I had bought a new oil level sensor since I've never gotten a dash warning since I bought the car last year. Yes, the dash warning light works during the key on...
  11. Replies
    26,149
    Views
    6,190,557

    Fixed the link in my post. Here it is again, more...

    Fixed the link in my post. Here it is again, more than enough for this project plus wherever else anyone could find a use for it
    ...
  12. Keep your eyes peeled for used on Fleabay. Picked...

    Keep your eyes peeled for used on Fleabay. Picked mine up for $45 shipped, ashtray and all and it barely looked used, lid wasn't even scratched. Better than the one it replaced for sure
  13. Replies
    10
    Views
    10,941

    Just wanted to add to this discussion as I just...

    Just wanted to add to this discussion as I just did this this weekend.

    Agreed. In fact, Dynamat explicitly describes this exact process. While I admit the factory crayon garbage had deteriorated...
  14. Replies
    26,149
    Views
    6,190,557

    Imo, there isn't any room back in that area for...

    Imo, there isn't any room back in that area for anything of any substantial dimension height-wise. It's pretty tight and I didn't want to put any additional pressure on the glass and louver, just...
  15. Replies
    26,149
    Views
    6,190,557

    Thanks! Just below the bottom of the back...

    Thanks!

    Just below the bottom of the back glass the steel panel has raised areas and those make contact with the molded-in support ribs of the louver. I installed adhesive Teflon tape on the steel...
  16. Replies
    26,149
    Views
    6,190,557

    Spent the better part of the weekend stripping...

    Spent the better part of the weekend stripping all the factory hot crayon sound-deadening, tar and insulation from the rear seat, trunk and shelf and replaced it with Dynamat and 1/2" Dynaliner. Took...
  17. Pm'd

    Pm'd
  18. Replies
    1,110
    Views
    366,319

    Sticky: Done. PM or email me ...sparky300 at gm

    Done. PM or email me ...sparky300 at gm
  19. Replies
    1,110
    Views
    366,319

    Sticky: This tow hook license plate holder came with my...

    This tow hook license plate holder came with my car, I neither need it or want it. It's complete with all hardware and in near new condition.

    Given that these are not much more than $10 new, you...
  20. Replies
    341
    Views
    134,179

    I'm in 1. Wolfn8tr- 1 2. CakM3- 1 3. Karl...

    I'm in

    1. Wolfn8tr- 1
    2. CakM3- 1
    3. Karl Lazlo- 2
    4. Badclown- 1
    5. BP- 1
    6. ZHP-Brandon- 1
    7. Vas- 1
    8. Sockethead- 1
  21. Replies
    20
    Views
    10,569

    Wow. These seem like a bargain given the...

    Wow. These seem like a bargain given the fantastic condition that they're in. Almost makes me wish that I lived closer...and had a coupe...and leather...

    GLWS
  22. Replies
    4
    Views
    7,607

    I prob made it sound worse than it actually is....

    I prob made it sound worse than it actually is. It really was only the 3 inches of wiring to the solenoid that were closest to the refector and I took care of that with liquid electrical tape. I...
  23. Replies
    4
    Views
    7,607

    I agree, mine were no better after 14 years...

    I agree, mine were no better after 14 years baking inside the housing. This way there is very little manipulation of the existing solenoid wires and reduced chance of insulation damage. The only...
  24. Replies
    4
    Views
    7,607

    ZKW HID Bi-xenon solenoid connector/pins

    I thought I'd post this info up given that I recently did the Morimoto projector install on my '04 that had the burnt bowl issue. I did a comprehensive search and couldn't definitively find that...
  25. Replies
    83
    Views
    32,361

    This.

    This.
Results 1 to 25 of 41
Page 1 of 2 1 2