Thanks for all of the replies. I wish I could find them for ~$1000 for the set like I have read in some older posts...
Type: Posts; User: edlvrt
Thanks for all of the replies. I wish I could find them for ~$1000 for the set like I have read in some older posts...
dpark, did you buy them from seller "partscontainer"? If so, when you get the light, could you let me know if it came with the necessary bulbs, ballast, etc? I had sent the seller a message, and the...
Hey everyone, my passenger side bi-xenon is not working. After pulling it out of the car to troubleshoot, the insulation on all of the wires is breaking off. I don't have the time to re-wire it, and...
Sorry about the ZSP bumper. The previous owner backed into something and had it replaced. I was thinking this would be my opportunity to get the correct bumper!
Does anyone know of sources to...
Hey guys, its been a while since I posted on here last, but I've checked in from time to time to see whats new. I hope all is well with everyone.
A few weeks a go, I was rear ended at low speed....
Does anyone have any slight gear rattle at idle? I have Redline MTL in mine, and while the shifts are smooth, I can hear the gear lash at idle. Is this cause for concern? Should I look for a thicker...
I have an Excel spreadsheet in the cloud. One tab is for part receipts/insurance/registration costs, one tab is for service costs and intervals, and the last if for fuel fill ups/consumption/cost
Did you watch the engine temperature closely? Are your engine belts and pulleys in good condition? Keep in mind that the alternator and water pump use the same belt to run them, and if that belt...
I'll double check. Thanks
Good evening all
Recently my ZHP started giving low exterior air temps. It would be 50F outside, and the car would randomly show 32, 36, 45F, etc. Sometimes it would show the correct temp, but the...
Will do
I was in upstate South Carolina this weekend for a reunion and had some time to kill before driving home, so off to some twisty mountain roads on HW 178.
...
As a follow up, the alignment pin for the Koni FSDs should be directly behind the pinch bolt. I don't have a ride height measurement on hand, though
Dane, I thought you were running Meyle HD CABs. Maybe I am thinking incorrectly.
Sounds good. My belts and pulleys are fairly new and I am planning to do an oil change at the same time. Any particular gasket brand to look for?
I'm going to tackle mine soon as well. Do I need any parts/gaskets other than the housing gasket and 2 crush washers for the VANOS line?
Thanks
To one up the safety glasses, I wear a pair of safety goggles that forms a seal around your face and prevents fluids and debris from getting around the glasses frame. Glad to hear that you are ok
I don't know anything other than their website shows it as in development, but the folks at German Auto Solutions (who make the DISA rebuild kit) have CCV setup in the works......
...
I agree. But that's their policy. Now I know and hope to help others avoid that issue
90K
I just finished installing FSDs with my OEM springs. I decided to do everything while it was apart. I'll go back and check the receipts (I have an Excel sheet that gave prices from different...
Yeah, I ordered them back on Black Friday, and they had a $40 or so coupon for that day only. Even before the coupon, they were the lowest price that I could find. But because of the back-order...
I installed my Koni FSDs last weekend and have enjoyed the slightly smoother ride around town. Most of the roads here are straight, so I haven't had the chance to properly see how they perform on a...
Attached are pictures of the strut alignment pin/bump and the pinch bolt. Forgive the low image quality as they were taken at night on my phone with the wheels still on. I'll take ride height...
I did the install myself and reused the factory springs. My indy mechanic was happy with how the springs were seated before the assemblies were bolted onto the car. I don't see how the strut bodies...