Materials to Maintain Your ZHP IIIII Hand Protection IIIII Tools to Maintain Your ZHP

Search:

Type: Posts; User: sillieidiot

Page 1 of 20 1 2 3 4

Search: Search took 0.03 seconds.

  1. I was talking about the plastic part that holds...

    I was talking about the plastic part that holds the aluminum on the trim side. I assumed you lost those pieces. Not the orange pieces that are on the dash that hold them in.

    Well, the superglue...
  2. I usually use PascoFix's superglue to fix stuff...

    I usually use PascoFix's superglue to fix stuff like that. My body shop guy was the one that showed me what he uses. You still got to prep the area, clean/sand a bit. if there's a gap, use the filler...
  3. most people either do the retroquik solution from...

    most people either do the retroquik solution from TRS or they buy new AL headlights.
  4. Used to use the craftsman 3 ton jack, then moved...

    Used to use the craftsman 3 ton jack, then moved to the MaxJax portable lift. Then I had the Arcan one from Costco. Now I'm using the HF Daytona 1.5T jack
  5. Replies
    4
    Views
    279

    Just needs an alignment. They will loosen and...

    Just needs an alignment. They will loosen and pull it back towards the outside of the car to get it to the correct spec.
  6. Replies
    25,865
    Views
    4,427,649

    that's weird. tapping into the rear lights...

    that's weird. tapping into the rear lights shouldn't need any coding. The trigger wire can have as low as 3v to activate the relay.
  7. Replies
    12
    Views
    585

    Same question. I feel like since you've heard it...

    Same question. I feel like since you've heard it for so long, you can be very specific about when it happens which would help us to try to narrow it down more.

    only when turning? or have to be...
  8. Replies
    8
    Views
    743

    Nice job. This is one of the reasons why during...

    Nice job. This is one of the reasons why during install, I put all the drivers/controller inside of the headlight. Also keeps water away.
  9. Replies
    1
    Views
    446

    I'm guess all of those measurements are in...

    I'm guess all of those measurements are in inches?

    Are you trying to use the stock location and put the carpet back to cover it?

    Why can't you use cut sheet metal? Just need an angle grinder....
  10. Replies
    4
    Views
    528

    I haven't done it yet. But my plan was to buy a...

    I haven't done it yet. But my plan was to buy a used pumpkin in the ratio I want, then refurbish and install the LSD into that. then swap it out. Since used diffs are fairly cheap, you still save...
  11. Replies
    23
    Views
    1,647

    It affects all of the E46s. It's not if, it's...

    It affects all of the E46s. It's not if, it's when.
  12. Replies
    3
    Views
    317

    Can't read the picture, too small. But if...

    Can't read the picture, too small.

    But if you're on stop suspension, everything should be green. Have you done a suspension refresh yet? tie rods, fcab, etc.
  13. Yeah, I guess those prices would make sense. My...

    Yeah, I guess those prices would make sense. My friend got quotes to replace the HPFP on M240i and it was ~$400, just labor. Takes like at most 2 hours your first time DIY and you have all the tools....
  14. 1k for rim repair? isn't it like $150/wheel? ...

    1k for rim repair? isn't it like $150/wheel?

    Man, these numbers show how much I have been saving because I try to DIY everything and also have access to parts discounts lol

    of course, it's...
  15. Replies
    6
    Views
    394

    welcome

    welcome
  16. Replies
    9
    Views
    534

    Yeah, there's a thread on e46fanatics about it....

    Yeah, there's a thread on e46fanatics about it. His sister, which helped found the company with him, has taken over operations since. RIP Raj.
  17. thank god lol I was seriously going to buy it lol...

    thank god lol I was seriously going to buy it lol You saved me. Thanks.
  18. man, I would buy this if I had space for it.

    man, I would buy this if I had space for it.
  19. ugh I dislike the King's Auto Body guy lol

    ugh I dislike the King's Auto Body guy lol
  20. he's my exclusive body shop now. I like him. He...

    he's my exclusive body shop now. I like him. He has this OCD about doing shit right. But yeah, he tends to say that shit if he thinks you can't afford it lol Also, if you try to do custom shit, he...
  21. Replies
    852
    Views
    90,997

    They have it. The OE aspherical ones are blue...

    They have it. The OE aspherical ones are blue tinted and the line the separate the two parts doesn't go all the way from the top to bottom (and it's actually a line). The aftermarket ones are a...
  22. Replies
    160
    Views
    31,713

    :rofl

    :rofl
  23. I have a body shop, but he's in HB. Dunno if you...

    I have a body shop, but he's in HB. Dunno if you want to drive all the way down.

    https://www.yelp.com/biz/a1-auto-body-shop-huntington-beach-2?osq=a-one+auto+body
  24. Replies
    2
    Views
    257

    realoem says it's m6x16

    realoem says it's m6x16
  25. Replies
    852
    Views
    90,997

    that's purple? man it looks brown to me lol

    that's purple? man it looks brown to me lol
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4