Search:

Type: Posts; User: BustedBoat

Page 1 of 5 1 2 3 4

Search: Search took 0.04 seconds.

  1. Replies
    991
    Views
    94,925

    Sticky: All lemforder

    All lemforder
  2. Replies
    991
    Views
    94,925

    Sticky: Hey Guys, I'm going through new parts I have that...

    Hey Guys, I'm going through new parts I have that I ended up not using. Anyone have any use for a two front end links or a single pair of RTAB limiters?

    EDIT: Also a single Right Side Tie Rod. PN...
  3. Replies
    12
    Views
    967

    Hey guys, thanks for the quick responses, I did...

    Hey guys, thanks for the quick responses, I did try to wiggle it with the wheel on the other side still on the ground. Wheel play remained the same with a bit of play on the far side wheel as well. ...
  4. Replies
    12
    Views
    967

    They should be new. Is that still a possibility?

    They should be new. Is that still a possibility?
  5. Replies
    12
    Views
    967

    Premature Tierod failure?

    I purchased and installed new Lemforder tierods sometimes in late 2015 early 2016, so they can't have more than 40k miles. Most likely way less, but looking at the videos and my experience they feel...
  6. Replies
    0
    Views
    402

    AKG Motor and Tranny Mounts

    Hey Guys I'm always asking for help without ever giving back so I figured I'd try to give back to the community. With that being said I've decided to review the AKG 75D mounts after having them for...
  7. Replies
    10
    Views
    1,456

    May have found it. The idler pulley is incredibly...

    May have found it. The idler pulley is incredibly tough to turn.
  8. Replies
    10
    Views
    1,456

    How is it supposed to sound and or feel? I tried...

    How is it supposed to sound and or feel? I tried it a few weeks ago and I didn't feel anything abnormal, or at least like how the dried out idler and tensioner pulleys felt like.

    And if you guys...
  9. Replies
    10
    Views
    1,456

    It does heh. Is there anything else that you can...

    It does heh. Is there anything else that you can possibly think of that dries out like that? Any bearings maybe? May be a dumb question but should the tensioner pulley move at all while the engine is...
  10. Replies
    10
    Views
    1,456

    Unfortunately the car had already been running...

    Unfortunately the car had already been running when I saw this message. Sound is semi gone by the time it heats up. It is apparent when I'm engaging, especially when I don't give a lot of gas. So i...
  11. Replies
    10
    Views
    1,456

    Belt/Bearing Noise

    Hey Guys back again! I'm having a noise issue that's driving me up a wall. I can't seem to find any good information on it, so I've decided to make a new post. I'm getting an old bearing noise that's...
  12. Replies
    13
    Views
    1,420

    Good thing you got that fixed then!

    Good thing you got that fixed then!
  13. Replies
    7
    Views
    1,097

    Check your intake as others have suggested. I had...

    Check your intake as others have suggested. I had the same issue years ago. Really rough start with bad idle. Giving it a little gas solved it until the next start up. Turns out one of my injectors...
  14. Replies
    13
    Views
    1,420

    Check for tie rod play maybe? My car had quite a...

    Check for tie rod play maybe? My car had quite a bit of looseness while driving when my tie rods went. I believe the easiest way to check for this is to jack up the front of the car, lock your...
  15. Replies
    26
    Views
    4,367

    Hey everyone back at it again. I've been juggling...

    Hey everyone back at it again. I've been juggling school among other things, but I have once again attempted to attack the problem that's been eluding me since I first got the car. Let me first start...
  16. Replies
    26
    Views
    4,367

    Okay I will hunt down a fuel pressure gauge. A...

    Okay I will hunt down a fuel pressure gauge. A friend had lent me one but it wasn't working right. I did at one point but it was because of a stupid mistake I had made, and it was fixed within a day....
  17. Replies
    26
    Views
    4,367

    I didn't smell anything out of the ordinary. I...

    I didn't smell anything out of the ordinary. I did have the engine cover on. Not sure if thay will make too much of a difference but all I smelled was hot engine :D
  18. Replies
    26
    Views
    4,367

    As far as my own novice eyes saw there are no...

    As far as my own novice eyes saw there are no tears. Thanks for reminding me, there are times dependent on just how rough the start up was, there can be a rather strong smell of fuel. I honestly...
  19. Replies
    26
    Views
    4,367

    Hey Guys, so turns out the problem is back. The...

    Hey Guys, so turns out the problem is back. The Disa valve seemed to fix it momentarily before it little by little crept back. No codes are being thrown. Fuel pump has been replaced, battery was...
  20. Replies
    11
    Views
    2,084

    But at the same time there's a certain range that...

    But at the same time there's a certain range that works for the car right?
  21. Replies
    11
    Views
    2,084

    Actually doing some quick research i found out...

    Actually doing some quick research i found out that oz is about to release similar wheels. Is there any wayto sort of influence more concavity by changing the offset?...
  22. Replies
    11
    Views
    2,084

    Similar wheels to ADV 10.1?

    Hey fam, just popping in to see how everyone is doing and to get some brain juices flowing! As the poor college kid I am, I like to "window shop" for things i'd like to one day throw on my car. I...
  23. Replies
    26
    Views
    4,367

    Months and Months later, problem solved. I took...

    Months and Months later, problem solved. I took it to a shop, they said the intake runner valve was leaking. Is that the DISA valve? Either way all is solved and better. Thanks for your help everyone!
  24. Does inpa need to be used in conjunction with...

    Does inpa need to be used in conjunction with other programs? ive been trying to use it on its own. Also anyone have any idea what api error # 28 means?
    sorry for the blurriness....
  25. Just to go on a tangent, do any of you guys use...

    Just to go on a tangent, do any of you guys use INPA? Installing it has been a trip.
Results 1 to 25 of 116
Page 1 of 5 1 2 3 4