Sorry, hadn't logged in and forgot to set up notifications for this thread. I responded to your private message just now.
Thanks
Type: Posts; User: cparker
Sorry, hadn't logged in and forgot to set up notifications for this thread. I responded to your private message just now.
Thanks
Lightly used, great condition. $75 shipped OBO.
Does that same trick apply to both LED and incandescent tail lights? That looks like an incandescent light, mine are LED.
I was really hoping the turn signal trick was the issue... but I check and that's not it. I also just checked the wiring while I was out there and I don't see anything wrong. Tonight when I get home...
So I just got to work and when I got out of the car the driver's side taillight is stuck on, not the entire light but the left and right columns (brake lights?). I had to unplug the light to get it...
Replacement of the solenoid took care of the code.
It's cupping though, not regular wear. The rears have bad inside edge wear but not cupping. These tires only have 20-25k on them, they'd be fine if not for the abnormal wear.
Can anyone recommend a certain strut that will work well in my application? No track use, only daily driving, but need to be valved for lowering springs. ECS has Koni orange str.t kits that are...
Looks like I should've upgraded my struts. I'm at the tire shop now and I have cupping on the inside tread of both front tires. That indicates struts right?
My tires only have 25k on then and...
I'll have to check it out, but I don't recall that requirement. I installed them along with brand new OEM struts, I would've gone aftermarket if I'd known.... but that doesn't mean I didn't...
These.
http://www.ecstuning.com/BMW-E46-330Ci-M54_3.0L/Suspension/Springs/ES10799/
I installed HR springs marketed as "sport" springs for 330 with factory performance package last year. I had the alignment checked after installing the springs and they said it was ok, but there is a...
Depends on back spacing. 10mm spacers seem common and it looks like I have room but it seems to be some educated guesswork as to what will fit based on back spacing, ride height, and spring rate.
Thanks guys
Whatcha want for those black bolts?
I just ordered some 10mm spacers for all four corners, they come with silver bolts but I need black ones. The product details don't indicate what length bolts they come with. What length wheel bolts...
I've done my VANOS, I've checked the DISA for free movement, and I've got the latest DME software. I don't have the 2800RPM dip like before I rebuilt the VANOS, but the 4000RPM dip is alive and well....
Ok so... I have the nasty 4k power dip. I've been searching through the forums for an hour trying to get a clear understanding of how to fix it. I've read a lot of information stating that the Jersey...
Well, just in case someone down the road is in my same shoes I'm going to post up what I'm finding. I pulled the fuse (#30) and it looks good. I found 12V to ground at the hot pins at both plugs...
Must not be a common issue?
I'm getting an "intake actuator circuit open" fault code and the car has markedly reduced performance. I pulled resistance across the exhaust vanos solenoid and it's 12.2ohms, the intake solenoid is...
The three LED's in the far right hand column of my driver's side tail light quit working. I thought it was kind of strange that just those three like that quit.
I tried doing a search and couldn't...
Bled it through the bleed screw by the res. A lot of the loss was from swapping t-stats.
Sure enough, I drove it around some more after bleeding the hell out of it and a block down the street I...
I've added about 2.5 gallons so far but that includes quite a bit of bleeding. I did not take the extra steps to drain the motor of coolant so there probably was some residual.
Bled some more. Absolutely no bubbles coming out of the bleed screw now. Brought it up to temp, both rad hoses are hot and the fan is cycling on and off as if the motor is maintaining good temps...