Materials to Maintain Your ZHP IIIII Hand Protection IIIII Tools to Maintain Your ZHP
Page 2 of 3 FirstFirst 123 LastLast
Results 11 to 20 of 24
  1. #11
    Join Date
    Nov 2014
    Location
    Portland, OR
    Posts
    10,242
    Quote Originally Posted by anandoc View Post
    This is an awesome DIY. Keep up the great work!!
    Thanks!

    I added the front seats section, but that section is a little wanting in the photo department because I didn't have any photos when I did the seats back in February. Last section is the rear seats and rear "door" cards.

  2. #12
    Join Date
    Jan 1970
    Location
    Liberty Township, OH
    Posts
    37,935
    Nice contribution Curves. Thank you.

    S7 Edge, out
    Call Me Dane l 2/2004 330i ZHP l 18x8 ET45 BBS CK's wrapped with Michelin Pilot Sport AS3+ @ 245-40-18 l KW V1 Coilovers in front l KW V1 springs w/ Bilstein B8 dampeners in rear l BMW Performance Rotors l UUC StrutBarbarian l Racing Dynamics Rear Strut Bar l Jim Conforti Shark Injector l Light Birch Interior Trim l Bimmian Celly Mount l M3 Trunk Mat l l e90 Performance E-Brake & Shift Knob l M3 Tri-Stitched Boots l AL Headlight Retrofit with ZKW Lenses l CobyWheel Wrap w/M3 Stitching l LCM sw 4.5 triple blink and rear fogs l Maple Interior Trim

  3. #13
    Join Date
    Nov 2014
    Location
    Portland, OR
    Posts
    10,242
    Note to self: finish this DIY guide.

  4. #14
    Join Date
    Aug 2011
    Location
    Las Vegas, NV
    Posts
    5,877
    Impressive DIY.
    BAV Stage 1 - BlueBus - UltraGauge - V1 - Orion V4's - ARC-8's - Brembo 996
    TTFS Engine/SMG Tune/CSL 255 - SGT Headers/Sect 1/SCZA - Evolve Eventuri
    VIS XTS CF Hood - CF Lip/Console/Diffuser - OE CSL Trunk - BWS 500S 9k/11k

  5. #15
    Join Date
    Nov 2014
    Location
    Portland, OR
    Posts
    10,242
    Quote Originally Posted by WOLFN8TR View Post
    Impressive DIY.
    Thank you! I hope it's helpful to others. I sourced a lot of different info from different places while doing my swap, so I figured why not make a complete guide in one place.

  6. #16
    Join Date
    Nov 2016
    Location
    Charlotte, NC
    Posts
    3,130
    Damn, dude. This is some next level DIY documentation.

    Did you put this together one night in DC after you had a few drinks and were flipping through pictures of your car, quietly weeping?

  7. #17
    Join Date
    Nov 2014
    Location
    Portland, OR
    Posts
    10,242
    Quote Originally Posted by ZHPizza View Post
    Damn, dude. This is some next level DIY documentation.
    Thanks, fam! It needs some work finishing up, but I thought it'd be helpful to us coupe folks. I still need to figure out the proper way to remove that plastic cover over the rear seat side bolster things underneath the seatbelt.

    Quote Originally Posted by ZHPizza View Post
    Did you put this together one night in DC after you had a few drinks and were flipping through pictures of your car, quietly weeping?
    I'm beginning to get the sense you think I may imbibe often. That may or may not be true, but my silent weeping is the least shameful aspect of my unconfirmed benders.

  8. #18
    Join Date
    Nov 2016
    Location
    Charlotte, NC
    Posts
    3,130
    Quote Originally Posted by BMWCurves View Post
    Thanks, fam! It needs some work finishing up, but I thought it'd be helpful to us coupe folks. I still need to figure out the proper way to remove that plastic cover over the rear seat side bolster things underneath the seatbelt.
    This one?



    You got the proper method. I just tore out my interior yesterday and figured this out along the way.

  9. #19
    Join Date
    Nov 2014
    Location
    Portland, OR
    Posts
    10,242
    Yessir. I lost the pin deep into the recesses of the car on that side so I had to buy a replacement pin/plug/doodad afterwards. I don't know if I actually installed it now that I think about it...

  10. #20
    Join Date
    Nov 2014
    Location
    Portland, OR
    Posts
    10,242
    Also, if you see any improved methods along the way, let me know. I'm no genius, but I'd like to have an effective guide.

Page 2 of 3 FirstFirst 123 LastLast

Similar Threads

  1. Is it too loud?? **Sound Deadening Project**
    By Rovert in forum Projects
    Replies: 37
    Last Post: 05-22-2017, 10:10 AM
  2. Convertible interior swap?
    By jwalther in forum General -- ZHP Related
    Replies: 6
    Last Post: 05-05-2016, 03:05 PM
  3. Help me decide?? Interior Swap pics inside...
    By JupiterBMW in forum Everything Non ZHP (the place for non-ZHP photos)
    Replies: 34
    Last Post: 06-07-2015, 04:47 PM
  4. Interior Swap Questions
    By ziazhp in forum General -- ZHP Related
    Replies: 5
    Last Post: 11-27-2014, 06:38 AM
  5. Interior Change/Swap Out
    By RyanOsiecki in forum Projects
    Replies: 5
    Last Post: 04-03-2011, 02:24 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •