Materials to Maintain Your ZHP IIIII Hand Protection IIIII Tools to Maintain Your ZHP
Page 12 of 13 FirstFirst ... 210111213 LastLast
Results 111 to 120 of 127
  1. #111
    Join Date
    Nov 2017
    Location
    Irvine, CA
    Posts
    818
    Quote Originally Posted by t.er View Post
    I'm on Tapatalk and can see them - it's odd but I've had issues where I can see it from the app, but on a browser on desktop the pics appear broken
    Quote Originally Posted by sillieidiot View Post
    hmm i can't see those last 3 pictures you posted.
    Quote Originally Posted by fredo View Post
    I'm on the browser on my laptop. One hour ago I saw the pics. Now they are broken.
    I re-linked (is that even a word?) the photos. Hoping they work now.

  2. #112
    Join Date
    Nov 2016
    Location
    SF Bay
    Posts
    613
    subbed, even if it's been a while since an update. I like that the car is the same color as mine too

  3. #113
    Join Date
    Nov 2017
    Location
    Irvine, CA
    Posts
    818
    It's been a long time since I updated so here we go.

    Replaced the cowl trim, back in 10/16/2020:










  4. #114
    Join Date
    Nov 2017
    Location
    Irvine, CA
    Posts
    818
    Another update from 12/22/20, control arms and FCAB.

    Alignment to check and set toe afterwards. That's a z4m 27mm front sway I added a while ago, nice and sharp turn-in.

















  5. #115
    Join Date
    Jun 2021
    Location
    Englewood, NJ
    Posts
    69
    Hey Will, I did my control arms a little while back and im sort of concerned about the torque process. Did you load the suspension when you torqued everything? I used a jack to lift up the suspension a bit and then tightened everything down like that.

  6. #116
    Join Date
    Nov 2017
    Location
    Irvine, CA
    Posts
    818
    Quote Originally Posted by REF84 View Post
    Hey Will, I did my control arms a little while back and im sort of concerned about the torque process. Did you load the suspension when you torqued everything? I used a jack to lift up the suspension a bit and then tightened everything down like that.
    Hi. I think I used the jack on the bottom of the ball joint when I torqued those two nuts, but that was to hold the arm / ball joint in position rather than to add any preload.

    I don't think the front control arms need to be preloaded to standard ride height for tightening. I know the rear ball joints do.

  7. #117
    Join Date
    Nov 2017
    Location
    Irvine, CA
    Posts
    818
    A photo break from ZHP stuff. I live somewhat nearby the Porsche Experience Center in Carson, CA. They have their Porsche Motorsport workshop, a display area, a cafe and a nice restaurant. Their workshop has a glass wall. I want a workshop like this, and those cars too. I took my parents to go check it out.

    This was out front, probably just a display piece but cool nonetheless:





    Inside:





    On the patio at the cafe:


  8. #118
    Join Date
    Nov 2017
    Location
    Irvine, CA
    Posts
    818
    Some ZHP stuff:


    From 7/2021:



    Had to clean out the windshield washer fluid. It grew this goop, clogging up the washer pump.




    Drive out to Austin, TX for the F1 race:

    First time road tripping east. I used to go to PDX annually.

    Around Ft. Hancock, TX:



    At the rest stop on the 10 just east of 190:



    A great dinner in Ozona, TX. I love a good country fried steak:



    At COTA in Austin, TX. Near the bridge by the esses during qualifying:





    On the pit straight, at end of qualifying and for the w-series race:










    Some BBQ. It was all delicious.

    I think Ironworks:


    I think Terry Blacks:


    On the road again, forgot where in Texas:




    Westward, back to socal:


  9. #119
    Join Date
    Nov 2017
    Location
    Irvine, CA
    Posts
    818
    Shortly after I arrived home from Austin, TX I went on another roadtrip.

    Back to PDX. I love the scenery along the 5. Over the grapevine, then as the landscape changes into northern California and into Oregon:





    I love seeing Mt Shasta:








    In the middle of trip some jackass decided to kick my rear view mirror in the middle of the night when parked at the hotel.

    Infuriating:





    Will fix when I get home. For now, duct tape to the rescue:


    More Oregon. I always like to head to the coast. The drive is wonderful and the scenery awesome:







    And always nice to have lunch and ice cream at the creamery:



    And the coast:






    And southward bound towards socal. I love the scenery:





    Then 4 months later finally found a suitable replacement mirror:

    Last edited by Will; 07-07-2023 at 07:29 PM. Reason: forgot to tag Shasta

  10. #120
    Join Date
    Nov 2017
    Location
    Irvine, CA
    Posts
    818
    Long Beach GP:





















    And one of the ZHP. Happened to park adjacent to a white e92 m3:




Page 12 of 13 FirstFirst ... 210111213 LastLast

Similar Threads

  1. Engine Replacement
    By SureShot434 in forum Performance
    Replies: 163
    Last Post: 08-19-2020, 05:44 PM
  2. Replies: 290
    Last Post: 10-03-2019, 08:29 AM
  3. Just joined; '04 coupe AW/Blk project car
    By Will in forum New Members (or older members who have not introduced themselves)
    Replies: 10
    Last Post: 11-30-2017, 07:06 PM
  4. Lorenzo's ZHP Coupe Project
    By Lorenzo in forum Projects
    Replies: 60
    Last Post: 02-07-2016, 10:05 AM
  5. Engine and Transmission Mount Replacement
    By Hornung418 in forum Maintenance
    Replies: 12
    Last Post: 12-12-2012, 05:31 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •