Call Me Dane l 2/2004 330i ZHP l 18x8 ET45 BBS CK's wrapped with Michelin Pilot Sport AS3+ @ 245-40-18 l KW V1 Coilovers in front l KW V1 springs w/ Bilstein B8 dampeners in rear l BMW Performance Rotors l UUC StrutBarbarian l Racing Dynamics Rear Strut Bar l Jim Conforti Shark Injector l Light Birch Interior Trim l Bimmian Celly Mount l M3 Trunk Mat l l e90 Performance E-Brake & Shift Knob l M3 Tri-Stitched Boots l AL Headlight Retrofit with ZKW Lenses l CobyWheel Wrap w/M3 Stitching l LCM sw 4.5 triple blink and rear fogs l Maple Interior Trim
I upgraded to the brass bleeder screw.
IIRC, there was another thread not too long ago about someone else who had a bleeder screw crack (not this guy).
Suppose the plastic won't be bad if you regularly change your tank/hoses/cooling system etc.
Johnny
2004 Imola Red over Black Leather. 6-MT, Navigation, Cold Weather Pkg (the wife loves them seat warmers!), 3.46 Diff, UUC Short-Shift Kit, Tranny Mounts, CDV Delete and iPod mount.
-Be yourself; everyone else is already taken.
ZHP Pre-Ride Briefing
2005 ZHP, Alcantara, Silver Cube, Nav, Sharked, BMW Perf Intake, BMW Perf CF Strut Brace, CF Valve/Fuel Rail Covers,
Shadowline Grills, CF Splitters, Fog Light Inserts, Euro-mirrors, CDV Delete, Beisan vanos, GAS DISA, BP Coded
Call Me Dane l 2/2004 330i ZHP l 18x8 ET45 BBS CK's wrapped with Michelin Pilot Sport AS3+ @ 245-40-18 l KW V1 Coilovers in front l KW V1 springs w/ Bilstein B8 dampeners in rear l BMW Performance Rotors l UUC StrutBarbarian l Racing Dynamics Rear Strut Bar l Jim Conforti Shark Injector l Light Birch Interior Trim l Bimmian Celly Mount l M3 Trunk Mat l l e90 Performance E-Brake & Shift Knob l M3 Tri-Stitched Boots l AL Headlight Retrofit with ZKW Lenses l CobyWheel Wrap w/M3 Stitching l LCM sw 4.5 triple blink and rear fogs l Maple Interior Trim
Hankook Ventus V4's 205/55/16 | 16" BMW OE Style 45's | ECSTuning 15mm Spacers | Thule 45050 Crossroad Rack | Thule 870XT Fairing | LLumar 35%/20% Tint
Custom Vienna Austria Euro Plate | GoMiniGo "No-Holes" License Plate Bracket | Smoked License Plate Cover | Black License Plate Frame | Khoalty LED License Plate Lights
I've been using a brass screw since overhauling my cooling system last summer. The original bleeder screw is in the trunk with an extra expansion tank cap (just in case!)
My dad swears by them.
I would just be careful not to overtorque the brass bleeder screw. I bet it would eat through the plastic threads on that elbow. Then you'd need to carry an elbow in the trunk too.
Hankook Ventus V4's 205/55/16 | 16" BMW OE Style 45's | ECSTuning 15mm Spacers | Thule 45050 Crossroad Rack | Thule 870XT Fairing | LLumar 35%/20% Tint
Custom Vienna Austria Euro Plate | GoMiniGo "No-Holes" License Plate Bracket | Smoked License Plate Cover | Black License Plate Frame | Khoalty LED License Plate Lights
My plastic bleeder screw has 125,000 miles on it. I suppose you could get a million outta the brass one.
Call Me Dane l 2/2004 330i ZHP l 18x8 ET45 BBS CK's wrapped with Michelin Pilot Sport AS3+ @ 245-40-18 l KW V1 Coilovers in front l KW V1 springs w/ Bilstein B8 dampeners in rear l BMW Performance Rotors l UUC StrutBarbarian l Racing Dynamics Rear Strut Bar l Jim Conforti Shark Injector l Light Birch Interior Trim l Bimmian Celly Mount l M3 Trunk Mat l l e90 Performance E-Brake & Shift Knob l M3 Tri-Stitched Boots l AL Headlight Retrofit with ZKW Lenses l CobyWheel Wrap w/M3 Stitching l LCM sw 4.5 triple blink and rear fogs l Maple Interior Trim
My bleeder screw is leaking right now. I'm afraid to drive my car. Since I need my car, though, I'll just hoof it up to the stealership (if they have one in stock) and pick it up rather than risk driving and having the irony of a failed bleeder screw on the way to pick up a bleeder screw.
When I install it, with the engine cold, will I need to re-bleed?