Big Earner
First Aid Kit Front Seat..what kind of screw?
So I got this container and bracket for my front seat for $20 without any mounting accessory and I'm wondering how I can find what size of screw I need that'll fit into the hole of the front seat where the brackets are mounted. I see the mounting holes under the seat though!
--Trevor--
Vancouver, BC
Messaggero
Trevor, I just removed my first-aid box to see how it is attached for you, and in my car the unit just slips in under the pass. seat. There is a plastic tab in the center that has to be pushed up to remove it, but to install it, it literally just slips in place over the two plastic channels on the seat bottom, and the latch locks it in place so that it cannot move forward. I hope that this helps!
Capo di tutti capi
Post #1 , #8, #33
http://forums.bimmerforums.com/forum....php?t=1098829
Pic here shows the mounting hardware if it helps.
http://www.ecstuning.com/BMW-E46-325...Box/ES1928374/
Call Me Dane l 2/2004 330i ZHP l 18x8 ET45 BBS CK's wrapped with Michelin Pilot Sport AS3+ @ 245-40-18 l KW V1 Coilovers in front l KW V1 springs w/ Bilstein B8 dampeners in rear l BMW Performance Rotors l UUC StrutBarbarian l Racing Dynamics Rear Strut Bar l Jim Conforti Shark Injector l Light Birch Interior Trim l Bimmian Celly Mount l M3 Trunk Mat l l e90 Performance E-Brake & Shift Knob l M3 Tri-Stitched Boots l AL Headlight Retrofit with ZKW Lenses l CobyWheel Wrap w/M3 Stitching l LCM sw 4.5 triple blink and rear fogs l Maple Interior Trim
Messaggero
My bad - couldn't see the bracket in the dark! Thanks, DW!
Capo di tutti capi
Just trying to help out humanity.
Call Me Dane l 2/2004 330i ZHP l 18x8 ET45 BBS CK's wrapped with Michelin Pilot Sport AS3+ @ 245-40-18 l KW V1 Coilovers in front l KW V1 springs w/ Bilstein B8 dampeners in rear l BMW Performance Rotors l UUC StrutBarbarian l Racing Dynamics Rear Strut Bar l Jim Conforti Shark Injector l Light Birch Interior Trim l Bimmian Celly Mount l M3 Trunk Mat l l e90 Performance E-Brake & Shift Knob l M3 Tri-Stitched Boots l AL Headlight Retrofit with ZKW Lenses l CobyWheel Wrap w/M3 Stitching l LCM sw 4.5 triple blink and rear fogs l Maple Interior Trim
Big Earner
Humanity thanks you! Haha
--Trevor--
Vancouver, BC
Campieri
I posted the bolts in my DIY :P Save you the trouble of finding proper lengths
http://www.zhpmafia.com/forums/showt...id-Compartment
Big Earner
Is there a special part no that I need to search for when I'm at Home Depot or Lowes? I'm not a screw guy...I have no idea what to ask for... :S I see you put there T30...but what about the length? I know when it's too long it'll interfere with the sliding of the front seat support for the thighs.
--Trevor--
Vancouver, BC
Campieri
the part number for the official screw used by BMW is 07 14 9 169 302. it's less than $1.00 retail a piece.
The pitch is M6x12. You can always do what Dane provide too.
Capo di tutti capi
Post 33 states,
"M6 x 1.0 x 16mm Pan-Head Machine screw (bought in the metric case at Home Depot) "
HTC Thunderbolt+TT
Call Me Dane l 2/2004 330i ZHP l 18x8 ET45 BBS CK's wrapped with Michelin Pilot Sport AS3+ @ 245-40-18 l KW V1 Coilovers in front l KW V1 springs w/ Bilstein B8 dampeners in rear l BMW Performance Rotors l UUC StrutBarbarian l Racing Dynamics Rear Strut Bar l Jim Conforti Shark Injector l Light Birch Interior Trim l Bimmian Celly Mount l M3 Trunk Mat l l e90 Performance E-Brake & Shift Knob l M3 Tri-Stitched Boots l AL Headlight Retrofit with ZKW Lenses l CobyWheel Wrap w/M3 Stitching l LCM sw 4.5 triple blink and rear fogs l Maple Interior Trim
Posting Permissions
Reply With Quote
