Post your daily ZHP/BMW/MINI pics!

Quote:

---

Originally Posted by RUS_ZHP

My tires are square as well at 225. I think I just being to cheap and didn't bother to buy spacers.
I run the similar combination on my red zhp. I have staggered wheels, but square 205 wheels, which are even weirder. Not to mention that I cannot push on gas pedal in the corners.
You made me think about spacers Botond.


Sent from my iPad using Tapatalk

---

I actually have spacers as well. 12.5mm all around, for effective offsets of +34.5 and +37.5.
Unfortunately I don't have any shots showing the angle down the side of the car, so this is the closest I've got:


https://farm1.staticflickr.com/390/3...d9dee4f5_b.jpg

Quote:

---

Originally Posted by az3579

I actually have spacers as well. 12.5mm all around, for effective offsets of +34.5 and +37.5.
Unfortunately I don't have any shots showing the angle down the side of the car, so this is the closest I've got:


https://farm1.staticflickr.com/390/3...d9dee4f5_b.jpg

---

What setup are you sitting on? Front looks good

Sent from my ZTE A2017U using Tapatalk

https://uploads.tapatalk-cdn.com/201...51ca2abb87.jpg

Quote:

---

Originally Posted by 3LiterStraightSix

What setup are you sitting on? Front looks good

Sent from my ZTE A2017U using Tapatalk

---

Bilstein PSS10's. I have to use spacers to clear the Wilwood BBKs, and figured 12.5mm pushes the 68's to right around where my BBS CH's are naturally without them (et35), which look perfect to me. Rear fenders are rolled.

Quote:

---

Originally Posted by Rovert

https://uploads.tapatalk-cdn.com/201...51ca2abb87.jpg

---

Dope!

Sent from my SM-G900V using Tapatalk

Quote:

---

Originally Posted by az3579

Bilstein PSS10's. I have to use spacers to clear the Wilwood BBKs, and figured 12.5mm pushes the 68's to right around where my BBS CH's are naturally without them (et35), which look perfect to me. Rear fenders are rolled.

---

You actually rolled? I've been weighing the options and think i might go the dremel cut and anti rust paint route.

Sent from my ZTE A2017U using Tapatalk

Quote:

---

Originally Posted by 3LiterStraightSix

You actually rolled? I've been weighing the options and think i might go the dremel cut and anti rust paint route.

Sent from my ZTE A2017U using Tapatalk

---

This is probably the better option. It's been done for a long time now, so I haven't bothered to cut it off.

Quote:

---

Originally Posted by 3LiterStraightSix

You actually rolled? I've been weighing the options and think i might go the dremel cut and anti rust paint route.

Sent from my ZTE A2017U using Tapatalk

---

That's what I did, but the Dremel did not have nearly enough dick to cut through the layers of fender lip. I had to bust out the angle grinder.

Quote:

---

Originally Posted by ZHPizza

That's what I did, but the Dremel did not have nearly enough dick to cut through the layers of fender lip. I had to bust out the angle grinder.

---

All i have is a dremel as of now... Sounds like a trip to the local harbor freight... Man i love that store for cheap shit

Sent from my ZTE A2017U using Tapatalk

Quote:

---

Originally Posted by ZHPizza

That's what I did, but the Dremel did not have nearly enough dick to cut through the layers of fender lip.

---

TWSS


So sorry, I had to. :rofl