What did you do for your ZHP/ BMW / MINI today? #2

^^ Is there a DIY for servicing the sun-roof + recalibration? If not, would you mind writing one up for the rest of us :p

Quote:

---

Originally Posted by anandoc

^^ Is there a DIY for servicing the sun-roof + recalibration? If not, would you mind writing one up for the rest of us :p

---

Try this Anando.

http://www.zhpmafia.com/forums/showthread.php?t=338


Thumbs, iPhone, TaT.

Quote:

---

Originally Posted by ELCID86

Try this Anando.

http://www.zhpmafia.com/forums/showthread.php?t=338


Thumbs, iPhone, TaT.

---

Thanks Shawn!!

Quote:

---

Originally Posted by anandoc

^^ Is there a DIY for servicing the sun-roof + recalibration? If not, would you mind writing one up for the rest of us [emoji14]

---

Yeah remove the sunroof and weld in a delete panel.

1. Turn your ignition to on but do not start the engine, AC position
2. Hold the moonroof button back to fully open the roof and hold it, the moonroof will go back and once its there KEEP holding the button back for about 20-30 seconds. (There will be no acknowledgement of doing this.)
3. Next push the button forward all the whole way, the moonroof will go forward and close, once it's closed KEEP holding the button forward until the moonroof goes up to the vent/tilt position.
4. Now depress the button (upwards) to tilt/lift the moonroof, even though it is already tilted and HOLD for approximately 20~30 seconds until the moonroof tilts up one level higher and then back to normal tilt.
5. Let go of the moonroof tilt button.

There.....all reset and calibrated!

Quote:

---

Originally Posted by Rovert

1. Turn your ignition to on but do not start the engine, AC position
2. Hold the moonroof button back to fully open the roof and hold it, the moonroof will go back and once its there KEEP holding the button back for about 20-30 seconds. (There will be no acknowledgement of doing this.)
3. Next push the button forward all the whole way, the moonroof will go forward and close, once it's closed KEEP holding the button forward until the moonroof goes up to the vent/tilt position.
4. Now depress the button (upwards) to tilt/lift the moonroof, even though it is already tilted and HOLD for approximately 20~30 seconds until the moonroof tilts up one level higher and then back to normal tilt.
5. Let go of the moonroof tilt button.

There.....all reset and calibrated!

---

Why do you need to do this? What is there to re-calibrate? The auto open/close?

Oh after fooling around and trying to put my shade back on the tracks, I missed putting the rear motorized slider into the right place so it confused the system and it started freaking out. When I hit close it would open. LOL. So I installed everything right and I did the reset and it's all good now.

Quote:

---

Originally Posted by Rovert

Oh after fooling around and trying to put my shade back on the tracks, I missed putting the rear motorized slider into the right place so it confused the system and it started freaking out. When I hit close it would open. LOL. So I installed everything right and I did the reset and it's all good now.

---

Gotcha.

Little bit of XPEL wrapping the front bumper!

Attachment 20783

Attachment 20784

Checking for any rear subframe cracks while he does the bumper:

Attachment 20785

Attachment 20786

Sucking out any air bubbles from when the hood and fenders were XPEL wrapped a couple months ago:

Attachment 20787

My car found an Estoril friend getting wrapped tomorrow! My car was a little shy as you can see...

Attachment 20788

^whats you feedback on the clear bra? DIY'able or PTM (pay the man)?


Thumbs, iPhone, TaT.