His - 2004 Imola Red / Alcantara 330i | 6MT | ZHP |
Her's - 2005 Black Sapphire Metallic / Black Leather 330i | 6MT | ZHP |
So found a really good BMW specialist here and what we found after rechecking is that there are no vacuum leaks with a high degree of certainty.
We did find that the fuel correction value in the ECU was stuck at 12%. He said this should change based on O2 signals and MAF readings and RPM. Wasn’t moving even with MAF disconnected. He actually said MAF was reading correctly.
I had the shark injector tune on the car so I reverted back to stock and saw the same thing. The value is an internal tune value so not sure why it’s stuck.
I’m planning on taking it to have the ECU reflashed to factory and then have the dinan stage 3 put on it as they should be able to do both at the same price and see what we have.
Sent from my iPhone using Tapatalk
2005 Dinan 6 Speed
1995 MR2 Turbo
1993 MR2 NA (Sold... first car)
2003 Jetta Wagon TDi 6 Speed (RIP)
I don’t remember, but from what he was telling me that should have been moving around with throttle input and when he was spraying some brake cleaner into the pcv system when we were looking for vacuum leaks. And it never changed.
The only concern I have is an issue in the ecu caused by the shark injector tuner since basically the whole manual is a warning about damaging your ECU.
My plan is to take it to a dealership that can do a software update and install fresh on the car, and potentially put a Dinan stage 3 tune since it has throttle body, exhaust, and intake and check the trim value again.
Sent from my iPhone using Tapatalk
2005 Dinan 6 Speed
1995 MR2 Turbo
1993 MR2 NA (Sold... first car)
2003 Jetta Wagon TDi 6 Speed (RIP)
Your mechanic should have noted the short/long term fuel trims at idle and at 2500. If the numbers dropped down when the engine rpm was increased, it would point to a vacuum leak. If the numbers did not change, the you are either looking at pre-cat o2 sensors, maf sensor or a fuel related issue ( fuel filter or fuel pump )
Spraying brake cleaner is not the proper way to diagnose vacuum leaks on these cars. You need to use a smoke machine which would easily pin-point any small or big leaks.
However if the fuel trims were at 12% which are really high, I would look into points of entry after the maf sensor like the disa o-ring or the throttle body boots. You can remove the disa and see if the o-ring is seated properly or inspect the throttle body boots for any tears. But you also mentioned that the car ran better with the maf disconnected so cleaning it with some maf cleaner could yield some improvements.
His - 2004 Imola Red / Alcantara 330i | 6MT | ZHP |
Her's - 2005 Black Sapphire Metallic / Black Leather 330i | 6MT | ZHP |
So the DISA has been replaced and we are replacing all 4 of the O2 sensors. I’m also going to go ahead and order the boots so I have those done too.
We were going to recheck the O2 sensor function and the fuel trim again. I have the fuel pump and filter on the list for next months car budget.
Sent from my iPhone using Tapatalk
2005 Dinan 6 Speed
1995 MR2 Turbo
1993 MR2 NA (Sold... first car)
2003 Jetta Wagon TDi 6 Speed (RIP)
Pulllling this one back up. So I get the car back from paint today, and going to get back to work. Just a quick update on whats been done and whats getting done.
Work Completed (updates in Bold):
- New Dinan Air Filter
- New MAF
- New Upper Intake Boot
- DISA Valve Replaced (New)
- New Plugs
- New Coil Packs
- New Upstream and Downstream O2 Sensors
- Reflash of ECU to stock at BMW
- Fuel Trims Noted prior to Reflash, will be getting them rechecked
- New Main Fuel Pump and Fuel Filter
Even after all this, car still has some weird low end hesitation and issues up top occasionally. Read a few places that Cam Position Sensors may cause issues with low end problems so this is what I have next:
- Intake and Exhaust Cam Position Sensors
- Lower Intake Boot (ordered)
- CCV System (although didn't seem to have any blockages when it was in the shop)
To continue the discussion on fuel trims... I don't know what the numbers mean in context but below is the print out I got from BMW. I plan on taking the car back in and having them pull the trims again since I've put some miles on the car since this measurement was taken and the ECU was reflashed:
- Adaptation, mixture, bank1, additive: 0.72 mg/Hub
- Adaptation, Mixture, Bank 2, additive: 0.44 mg/Hub
- Multiplicative bank 1, mixture adaptation: -8.00%
- Multiplicative bank 2, mixture adaptation: -8.00%
2005 Dinan 6 Speed
1995 MR2 Turbo
1993 MR2 NA (Sold... first car)
2003 Jetta Wagon TDi 6 Speed (RIP)
Nice werk
Sent from my SM-G935V using Tapatalk
Randeaux/Rando/John/jr - '06 Cic ZHP; Southern California
"ZHP or not, I still like you"
ZHP Performance Package, Cold Weather Package, Leather, Jet Black/Black/BlackCube, NAV, Anthracite Black "my individual" interior trim
ESS Stage 1 Twin Screw Supercharger, Sprint Booster, BMW Perf Intake, Magnaflow Exhaust, Dinan TB & STEP S/W, UCC Sway Bars, Apex EC-7 18x8.5 ET38
Suspension: AST 44100 dampers, Bimmerworld front adjustable end links, Swift springs (8K front, 10K rear), Vorshlag camber plates
Dynavin D99+, Hardwire V1 (w/V1 Connection), BSW Stage 1 Speakers, Kicker Amp/Subwoofer
BMW Performance Strut Brace, Orion V2 Angel Eyes, No-holes License Plate, SMG Paddle Shift Mod, Besian VANOS, Gold DISA, Fan Delete, M3 Side Mirrors
Note: Actual car no longer resembles signature picture