Call Me Dane l 2/2004 330i ZHP l 18x8 ET45 BBS CK's wrapped with Michelin Pilot Sport AS3+ @ 245-40-18 l KW V1 Coilovers in front l KW V1 springs w/ Bilstein B8 dampeners in rear l BMW Performance Rotors l UUC StrutBarbarian l Racing Dynamics Rear Strut Bar l Jim Conforti Shark Injector l Light Birch Interior Trim l Bimmian Celly Mount l M3 Trunk Mat l l e90 Performance E-Brake & Shift Knob l M3 Tri-Stitched Boots l AL Headlight Retrofit with ZKW Lenses l CobyWheel Wrap w/M3 Stitching l LCM sw 4.5 triple blink and rear fogs l Maple Interior Trim
I think I diagnosed what's causing my car to be so twitchy and walk all over the damn place. Somehow both fronts are toed out. The right is toed out worse than the left, and it's (surprise surprise) pulling right.
I got the left back into "close enough" spec (using numbers I've pulled from what you guys have posted previously), but the right tie rod lockdown nut is stuck. I'm going by Firestone tomorrow to see if they'll break the nut loose and finger tighten it so I can adjust the toe at home. I don't want to pay for another professional alignment until after I do the oil pan gasket.
Emma - 2005 BMW 330ci ZHP 6MT Estorilblau Individual
Sportline 8s 18x8.5F - 18x9.5R | APEX ARC-8 18x8.5 Square | aFe Intake | 135i Brembo F/R Calipers | 26mm Front/20mm Rear Sway Bars | Z4 Mirror
M3 Dead Pedal | Lexus ES300 Yellow Fog Light Retrofit | Koni Yellows/H&R Springs | Llumar CTX 40% | Coby Tri-Stitch Wheel & Boots
Awaiting Install: M3 Wing Mirrors
Emma - 2005 BMW 330ci ZHP 6MT Estorilblau Individual
Sportline 8s 18x8.5F - 18x9.5R | APEX ARC-8 18x8.5 Square | aFe Intake | 135i Brembo F/R Calipers | 26mm Front/20mm Rear Sway Bars | Z4 Mirror
M3 Dead Pedal | Lexus ES300 Yellow Fog Light Retrofit | Koni Yellows/H&R Springs | Llumar CTX 40% | Coby Tri-Stitch Wheel & Boots
Awaiting Install: M3 Wing Mirrors
That's common with these cars, especially one that has seen salt. Don't be surprised if they have to use heat to free it up. If they do, your gonna want to paint that area because it will rust up real fast. Make sure you use anti-seize on the threads and you never have that problem again.
Dinan CAI &Throttle body, ESS Tuning TS2, Bimmerbrakes gen3 headers, UUC SSK & DSSR. Achilles oil pump, VAC oil pan baffle
M3 Motor mounts, UUC Trans mounts, Modified clutch style LSD 3.15, TMS front subframe reinforcement, Koni Yellow sports,
H&R sport springs, UUC sway bars, BMW Perf. Rotors, UUC SS brake lines, Hawk HPS pads, CSL replica wheels,
Rotora strut bar, FXR HID conversion, M3 Mirror conversion, BSW stage 1 speakers
Finally got my front Koni FSD's installed, 5K mi. after I put the rears in myself. It's hard to find a decent shop here which will accept customer-supplied parts.
2006 6MT Coupe, Alpine White • Premium, Cold Weather and Xenon packages
MFactory 3.38 LSD • 27mm M3 bar • ECS strut brace • Koni FSD's
Other tweaks: see my profile
Half-way into a wash and wax, though half-way might be optimistic
![]()