Derbo's ZHP

[Avetiso]

I don't think the MAF resets... it's there for measuring real-time, so I couldn't imagine any "reset" you could do to it.

Try cleaning the MAF? However, it shouldn't technically be a variable since getting rid of the aFe eliminated the code.

By the way, notice any difference returning to stock? What do you think?

[derbo]

Oops you are right Dario. It's just a sensor and it would just output. I meant fuel trim adaptations. Since I only drove 100 miles, I'm not 100% convinced the AFE was the problem. So many people have no issues with the AFE so it is a little hard to rule it as the problem. I will drive it more next week.

[Hornung418]

Anytime I complete a modification that would alter the AFM, I reset the adaptations. When you get your scanner working go into INPA and reset them.

[derbo]

Thanks guys, I'll fiddle with it later this week if I have time. Work is a killer ATM.

[wertyu78]

I've given up on the damn BMW Scanner to work on anything outside my old 2004 XP laptop. It refuses to work on VMware with an SP3 clean install, or Parallels XP SP3 clean install. I suspect it might be some issue with the mac side?


I got an SES on the way home, and low and behold, its the lean fuel trim on bank 1 and 2 again. DAMMIT! I need to smoke test the damn thing to see where this leak is coming. I fear it comes from the DISA valve..

LMK if you would like to me login remotely and setup XP Pro SP3 on your Mac. 404-660-4743

[derbo]

Thanks. Im positive XP was installed correctly. I'm looking at the console logs of Mac and I think there may be a conflict in drivers and assignment.

sent from Moto X Dev edition

[tkundhi]

Try VirtualBox, you should be able to migrate your Parallels or VMare image. I don't know how PA Soft will do. I have had a chance to try and install it yet.


Sent from my iPhone using Tapatalk

[derbo]

I've narrow it down to a problem with my USB port and Mavericks. It is not related to the VM installation as the methods I used were successful on a 2012 Macbook Air with no issues.

I have to remember if I did a dirty install of Mavericks or did I do a clean install. I don't remember. Perhaps its a nice time to just reinstall mavericks with a clean slate!

[JupiterBMW]

Damn Derek, just caught up to your thread, you've been battling headache after headache... I wish I could help more, but you guys are all smarter than I when it comes to this stuff. I'm just lucky mine is working. FWIW, I am running OSX 10.9.1... Hoping an update to 10.9.2 doesn't land me where you are...

As for your intakes. I have the boots that I took off my car when I put my Dinan TB on... They are about 20k miles old, but in great shape and still pretty soft. If you'd like, I can send them to you. I was going to donate them in the pay it forward thread anyway... LMK if you need them (text me) and I can send them out at some point..

[derbo]

Damn Derek, just caught up to your thread, you've been battling headache after headache... I wish I could help more, but you guys are all smarter than I when it comes to this stuff. I'm just lucky mine is working. FWIW, I am running OSX 10.9.1... Hoping an update to 10.9.2 doesn't land me where you are...

As for your intakes. I have the boots that I took off my car when I put my Dinan TB on... They are about 20k miles old, but in great shape and still pretty soft. If you'd like, I can send them to you. I was going to donate them in the pay it forward thread anyway... LMK if you need them (text me) and I can send them out at some point..

Thanks Joop! I already have brand new boots installed on the car. I'll have to do more mileage to determine if the AFE intake was the problem or not. (Possible just the little rubber ring from the MAF. Hopefully after this is solved, there are no other major issues to deal with!



Macbook issues:
I doubt 10.9.1 > 10.9.2 will make a difference as I just installed that yesterday. The issue seems to be related to my 2013 rMBP. My dad's 2012 MBA with USB3.0 manages to work the PA SOFT software. I hope its not a hardware issue. I've narrowed it down in the console logs to the USB not loading correctly. I need to determine if it is a software or hardware problem. From the looks of it, it seems to be software related. I might reinstall OSX 10.9.2 as a clean install and see if it is willing to work.